ERMFTT-1008

Model ERMFTT-1008

Fault Tolerant Transceiver

to plug into

ERM21C, 21 Slot Chassis

Features:

* Automatic MDI/MDIX detection

* Fast Link Pulse Generation: This feature allows auto negotiation partners to go full duplex.

* Ensures connection even if segment is damaged or sabotaged.

* User selectable configuration, TCVR to TCVR, or TCVR to HUB.

* Compact rugged steel enclosure.

* Designed and manufactured in the USA.

The ERMFTT-1008 is designed to obtain the highest level of data reliability

using redundant data paths. It does so by providing a main port and 2

redundant ports (A,B). The user can select either A or B the primary RJ45 port, by using

of the A/B select switch. The ERMFTT-1008 will only pass data on the

primary port, or on the active port in the case of a cable failure. The

transceiver will automatically return to the primary port when it senses

that this port has got a valid link.

LEDs.

All three ports have their own set of two LEDs for each of the following:

LINK/Activity, Indicates that a proper 100BaseTX link has been established at the port. LEDs for both ports (RJ45 connectors 2 & 3) should be ON during when a good link is present and when there is absence of data. The LED should blink when the data is passing through. The Link LEDs should be on if all connections have been made properly, if the cable is intact, and if the device on the other end of the cable is operational.

ENABLE, Indicates that the port is the one in use. Only one of the LEDs should be lit on at any given time in the "Hub" mode. Both enable LEDs should be on in the T-T (transceiver-transceiver) mode.

Locating ERMFTT-1008 transceivers.

The ERMFTT-1008 must be used in conjunction with the ERM21C, 21 slot rack-mount chassis, it simply plugs in and the set screw holds it firmly in place. Run a UTP cable from the work-station or network device to the ERMFTT-1008. A second and third UTP cables are then used to connect to another ERMFTT-1008 or a hub, or a switch. These cables can be up to 100 meters (328 ft.) in length. It is advisable to follow the Ethernet specifications for aggregate twisted pair lengths. EtherCom’s ERM12, EFM12, EFM14 or EFM15 twisted pair to fiber media converters may be utilized to extend these segments to 2 kilometers, single-mode versions can extend the segments to 15 or 100 kilometers using fiber optic media.

In the TCVR/TCVR (T-T) mode it does not matter which port on the first transceiver is connected to which port on the other transceiver, because the data is transmitted simultaneously on both A and B ports and will be received on only 1 port either the primary of the secondary. If both links are present on the receiving end, the data will be received by the primary port. In the event where the primary link is terminated, then the secondary port on the receiving end will be enabled.

The ERMFTT-1008 is fully compatible with Ethernet V2.0/IEEE 802.3 transceiver specifications for CSMA/CD 100 Mbps operation.

Switches

The set of four miniature slide switches on the front of the unit are:

· Switch 1, marked A - B, Selects either port A or port B as primary port.

· Switch 2, marked T-T - HUB, (Fault Tolerant Transceiver - Hub) Lets you set up the operation of the unit for transceiver to transceiver or transceiver to hub.

UTP Crossover Capability

The ERMFTT-1008 has an automatic MDI/MDIX detection feature, this eliminates the need for a specially configured UTP crossover cable. It allows a repeater or a non-repeater device to be attached to the UTP segment side.

FLP (Fast Link Pulses) Generation

The device generates fast link pulses upon the connection of the UTP cable on all 3 ports. This feature allows it's link partners to auto-negotiate to the full duplex mode so it can obtain the highest performance.

Monitoring

The unit is simple with the complement of 6 LEDs that display Link and Enable on each RJ45 connectors.

ERMFTT-1008 TECHNICAL SPECIFICATIONS

Network Standards	Ethernet V2.0/ IEEE 802.3
Speed	100 Mbps.
Half duplex	Yes
Full duplex	Yes
Power	From ERM21C
LEDs	Total 6	Enable & Link for each RJ45
Weight	0.2 lb.	91.0 g.
Dimensions	3.36” x 2.14“ x .73”	(8.84 cm x 5.25 cm x 2.09 cm)
Environmental	Operating Temperature Storage Temperature Relative Humidity	32 to 122F (0 to 50 C) -4 to 140F (-20 to 60 C) 5% to 80% (non-condensing)
Switches	2 exterior switches 2 position DIP switch 1 for unit to unit or for Unit to Hub. 1 for Priority Segment A/B
Connectors	3 Fully Shielded RJ45 connectors.
Cabling	UTP Category 5, maximum cable distance 100 meters
Regulatory Approvals	EMI FCC Class A & CE.
Warranty	5 years

EtherCom Corporation

1409 Fulton Place, Fremont, CA 94539, USA

Tel. (510) 440 0242 Fax. (510) 659 8296

www.ethercom.com